Challenger CL10AV3-DPC-QC Versymmetric 2-Post Adjustable Lift

This is the fully specified end of the CL10AV3 range, and the model number reads like a parts list: DPC for Dual Pendant Controls, QC for QuickCycle. Our record lists its configuration as Dual Pendant Controls & QuickCycle, and it is the QuickCycle half that carries the bigger 3 HP power unit and a 27 second speed of rise. Capacity is 10,000 lbs., on the same Versymmetric offset-arm platform the rest of the family uses.

If you are choosing between the variants, the short version is this: the pendants change where a technician can stand, the QuickCycle power unit changes how long they stand there. This page is about whether paying for both is justified by the work you do.

Where the cycle time actually goes

A rise time looks like a vanity number until you multiply it. A lift is raised and lowered several times on a single job - up to remove wheels, down to check a road-going fault, up again to torque, down to release. Across a day of short-interval work, seconds spent watching a lift travel are seconds nobody is paid for, and they arrive in the least useful shape possible: too short to start another task, long enough to break concentration.

Where that arithmetic works is express service - oil, tyres, inspections, brake jobs measured in tens of vehicles rather than hours per vehicle. Where it does not work is a shop where a vehicle goes up in the morning and comes down in the afternoon. For that shop the standard power unit is the honest recommendation, and it costs less.

Two pendants on top of that

The dual pendant half of this model is about position rather than speed. A control station on each column means the operator can stand on the side the vehicle was loaded from and watch the near pads take weight, instead of running the lift blind from a fixed post and walking around to check. In a bay where two technicians share a vehicle, each of them has controls in front of them. Combined with a power unit that moves quickly, the practical effect is that the lift stops being the thing everyone waits on.

Versymmetric geometry, in plain terms

Versymmetric offset front arms let one lift do symmetric and asymmetric work without being reconfigured. Asymmetric spotting sets the vehicle back so doors clear the columns - the right answer for a wide-door sedan whose occupants have to get out. Symmetric spotting centres the load between the columns, which is what a long pickup wants. Being able to choose per vehicle, rather than living with one compromise, is the whole argument for this arm design.

Front arms are 3-stage and reach 20 in. to 42 in.; rear arms are 3-stage and reach 37.625 in. to 60 in. Premium double telescoping screw pads adjust from 3.875 in. to 6.125 in., which covers most recommended lift points without a stack of adapters. The directSPOT front arm design is intended to end the reverse-and-retry routine that costs a bay a minute every time a vehicle is spotted wrong.

Built to be serviced, not just sold

The equalisation system uses an oversized 5 in. diameter pulley and heavy duty 5/16 in. cable - a larger pulley means a gentler bend radius on the cable and less stress per cycle, which is exactly what a shop running a high cycle count should care about. Each carriage is 48 in. elongated, spreading load down a longer run of column. The single-point lock release is pulley-less and jacketed, so one pull frees both columns and there is no release pulley to seize. Base plates are fully gusseted, arm restraints and pins are plated, and the finish is powder coat.

Will It Fit?

Built for a 12 ft. ceiling as standard, with 2 ft. or 3 ft. column extensions available. Floor to overhead switch runs 10 ft. 8.5 in. to 11 ft. 2.5 in. depending on setup.

Three width settings take the lift from 11 ft. 6.5 in. through to 12 ft. 6.5 in. overall, giving 110 in., 116 in. or 122 in. inside the columns and 100 in., 106 in. or 112 in. of drive-thru clearance between the carriages. Rise height at the top of the pad is 74.125 in., and maximum rise measured under the arms is 70 in.

One measurement to confirm before you commit to a ceiling. Published figures for the overall height differ: Challenger's specification block gives 11 ft. 2 in. or 11 ft. 8 in. by column setting, and 11 ft. 11 in. with the cylinder extended; the catalogue listing gives 143 in., 145 in. or 146 in. for the same measurement. If headroom is tight, confirm the overall height with us in writing before you order - we will get it straight from Challenger.

We do not hold Challenger's concrete thickness and strength specification in our own product data, so we will not quote you one. Ask us for the installation manual before you drill anything. Verifying the slab, the anchor spec, the ceiling clearance and the electrical supply is the buyer's responsibility, and it is far cheaper to do it with a tape measure than with a lift on the floor.

Power supply

3 HP, 208v-230v, 60 Hz, 1 Ph, with speed of rise listed at 27 seconds. That is a larger motor than the standard configuration of this lift carries, so if you are replacing an older unit do not assume the existing circuit is adequate. Have an electrician read the motor plate and size the supply before delivery.

Perfect For

• Express service lanes where vehicle count per bay per day is the number that matters.
• Tyre and quick-lube operations cycling a lift dozens of times a shift.
• Dealership service departments with two technicians working one vehicle.
• Busy independent shops replacing a slow lift that has become the bottleneck.

What's in the Box

• Two columns, fully gusseted base plates, 48 in. elongated carriages
• 3-stage front and rear arms, plated arm restraints and arm pins
• Premium double telescoping screw pads
• Pulley-less jacketed single-point lock release
• Padded overhead shut-off system
• Standard dual integrated rubber door guards

Red, blue or black. Accessories are ordered separately - tell us the work you do and we will tell you which of them you will actually use.

Certification, stated plainly

Our record for this configuration shows ALI and ETL certification marked yes. That is third-party listing rather than self-declaration, and it is the distinction that matters to an insurer, a fleet policy or a local inspector. If a listing is a condition of your cover or a contract you are bidding on, get the requirement in writing and let us match the certificate to the exact configuration before you order.

Shipping and Delivery

Freight only, within the lower 48 states. Plan for a forklift or a dock, or take terminal pickup instead; warehouse collection is available. Residential delivery can be arranged and carries a fee. This item ships free, so there is nothing to add at checkout.

Check the shipment before signing for it. Count cartons against the packing list, look for crush damage, punctures and banding that has been cut and retied, and record anything questionable on the bill of lading while the driver waits. Once it is signed clean, the carrier's part of the argument is over.

Warranty

Terms and the claim route are on our warranty claims page. No coverage period is printed here on purpose: our product data for this model holds a link, not a term, and inventing a duration would be worse than omitting one. Ask us and we will confirm what applies to this configuration.

Do not disassemble anything before a claim is raised. A power unit that has been opened or a column that has been stripped cannot be assessed, and that single step turns more good claims into disputes than any other. Photograph the fault, write down what the lift was doing, and leave it alone.