{"product_id":"nt-11-two-post-auto-lift","title":"Triumph NT-11 11,000 lb Two Post Auto Lift","description":"\u003ch2\u003eDescription\u003c\/h2\u003e \u003cp\u003eThe \u003cstrong\u003eTriumph NT-11\u003c\/strong\u003e is an \u003cstrong\u003e11,000-lb asymmetric two-post floor-plate lift\u003c\/strong\u003e built for full-time shop and serious home-garage use. Its two columns are joined at the floor by a drive-over base plate rather than an overhead crossbar, so there is no top bar to drop ceiling clearance — the tallest fixed point is the 116-inch column itself. The lift raises cars, trucks, vans, and SUVs up to its rated capacity, with the load split across four arm pads at \u003cstrong\u003e2,750 lb per pad\u003c\/strong\u003e.\u003c\/p\u003e \u003cp\u003eThe arms are \u003cstrong\u003easymmetric\u003c\/strong\u003e: the two front arms are three-piece double-telescoping sections, and the two rear arms are two-piece single-telescoping sections, so the vehicle sits rearward in the bay and the doors clear the columns when you load and unload. Each arm finishes in a rubber lift pad and accepts a set of stackable steel truck adapters for frames that need extra reach, up to a 9-inch maximum pad height. Lifting is handled by \u003cstrong\u003edual hydraulic cylinders\u003c\/strong\u003e — one per column — kept in sync by dual equalizer cables routed over top and bottom sheaves. A multi-position mechanical safety latch on each column engages automatically as the carriage rises and holds the lift on lock until both releases are pulled, and rack-and-gear arm restraints keep the swing arms from drifting under load.\u003c\/p\u003e \u003cp\u003eThe column-mounted electric-hydraulic power unit runs on \u003cstrong\u003e220V single-phase\u003c\/strong\u003e service (60 Hz, on a dedicated 30-amp circuit) and can be mounted on either column. It uses about 3 gallons of AW32 hydraulic oil and raises the lift to a \u003cstrong\u003e72-inch maximum height in 56 seconds\u003c\/strong\u003e, dropping to a 4.5-inch lowered height to clear low-profile vehicles. Both \u003cstrong\u003eISO 9001\u003c\/strong\u003e manufacturing and \u003cstrong\u003eCE\u003c\/strong\u003e conformity are stated by Triumph. The lift installs on a level concrete floor rated \u003cstrong\u003e4 inches minimum at 3,000 PSI\u003c\/strong\u003e, ships freight, and includes a set of truck adapters, floor anchors, and mounting hardware at no extra charge.\u003c\/p\u003e  \u003ch2\u003eFeatures\u003c\/h2\u003e \u003cul\u003e   \u003cli\u003e \u003cstrong\u003e11,000-lb lifting capacity\u003c\/strong\u003e, distributed at 2,750 lb per arm pad\u003c\/li\u003e   \u003cli\u003e \u003cstrong\u003eAsymmetric arm design\u003c\/strong\u003e — three-piece double-telescoping front arms, two-piece single-telescoping rear arms\u003c\/li\u003e   \u003cli\u003e \u003cstrong\u003eFloor-plate (drive-over base plate) design\u003c\/strong\u003e — columns join at the floor, no overhead crossbar\u003c\/li\u003e   \u003cli\u003eDual hydraulic cylinders, one per column, synchronized by dual equalizer cables\u003c\/li\u003e   \u003cli\u003eMulti-position mechanical safety latches with automatic engagement and dual manual release\u003c\/li\u003e   \u003cli\u003eRack-and-gear automatic arm restraints\u003c\/li\u003e   \u003cli\u003eRubber lift pads with a set of stackable steel truck adapters (9-inch maximum pad height)\u003c\/li\u003e   \u003cli\u003eColumn-mounted electric-hydraulic power unit, mountable on either side\u003c\/li\u003e   \u003cli\u003e \u003cstrong\u003e220V single-phase\u003c\/strong\u003e power unit, 60 Hz, on a 30-amp circuit\u003c\/li\u003e   \u003cli\u003e72-inch maximum lift height, 4.5-inch lowered height, 56-second lift time\u003c\/li\u003e   \u003cli\u003e \u003cstrong\u003eISO 9001\u003c\/strong\u003e manufacturing and \u003cstrong\u003eCE\u003c\/strong\u003e conformity stated by Triumph\u003c\/li\u003e   \u003cli\u003eTruck adapters, floor anchors, and mounting hardware included\u003c\/li\u003e \u003c\/ul\u003e  \u003cfigure\u003e   \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0771\/5550\/0318\/files\/nt-11-two-post-auto-lift-dimensions.webp?v=1780761721\" alt=\"Triumph NT-11 dimensions diagram: 116-inch overall height, 138-inch overall width, 112-inch between posts, 102-inch drive-through, 72-inch lift height, 4.5-inch lowered height.\"\u003e   \u003cfigcaption\u003eNT-11 dimensions per Triumph: 116\" overall height, 138\" overall width, 112\" between posts, 102\" drive-through, 72\" lift, 4.5\" lowered.\u003c\/figcaption\u003e \u003c\/figure\u003e  \u003ch2\u003eWhat's Included\u003c\/h2\u003e \u003cul\u003e   \u003cli\u003eTwo columns (powerside and offside) with carriages\u003c\/li\u003e   \u003cli\u003eDrive-over base plate (floor plate)\u003c\/li\u003e   \u003cli\u003eTwo hydraulic cylinders (one per column)\u003c\/li\u003e   \u003cli\u003eElectric-hydraulic motor power unit\u003c\/li\u003e   \u003cli\u003eFour asymmetric swing arms with rubber lift pads and pad holders\u003c\/li\u003e   \u003cli\u003e1-1\/2\" arm-mounting pins\u003c\/li\u003e   \u003cli\u003eRack-and-gear arm restraints\u003c\/li\u003e   \u003cli\u003eEqualizer cables and chains\u003c\/li\u003e   \u003cli\u003eHydraulic hoses\u003c\/li\u003e   \u003cli\u003eSet of stackable steel truck adapters\u003c\/li\u003e   \u003cli\u003eFloor anchors (3\/4\" × 5-1\/2\") and mounting hardware\u003c\/li\u003e   \u003cli\u003eInstallation and operation manual\u003c\/li\u003e \u003c\/ul\u003e  \u003ch2\u003eSpecifications\u003c\/h2\u003e \u003ctable\u003e   \u003ctr\u003e\u003cth colspan=\"2\"\u003eTriumph NT-11 Specifications\u003c\/th\u003e\u003c\/tr\u003e   \u003ctr\u003e \u003ctd\u003eLifting capacity\u003c\/td\u003e \u003ctd\u003e11,000 lbs\u003c\/td\u003e \u003c\/tr\u003e   \u003ctr\u003e \u003ctd\u003eCapacity per arm pad\u003c\/td\u003e \u003ctd\u003e2,750 lbs\u003c\/td\u003e \u003c\/tr\u003e   \u003ctr\u003e \u003ctd\u003eArm configuration\u003c\/td\u003e \u003ctd\u003eAsymmetric\u003c\/td\u003e \u003c\/tr\u003e   \u003ctr\u003e \u003ctd\u003eLifting height (max)\u003c\/td\u003e \u003ctd\u003e72\"\u003c\/td\u003e \u003c\/tr\u003e   \u003ctr\u003e \u003ctd\u003eLowered height\u003c\/td\u003e \u003ctd\u003e4.5\"\u003c\/td\u003e \u003c\/tr\u003e   \u003ctr\u003e \u003ctd\u003eLift time\u003c\/td\u003e \u003ctd\u003e56 seconds\u003c\/td\u003e \u003c\/tr\u003e   \u003ctr\u003e \u003ctd\u003eOverall height\u003c\/td\u003e \u003ctd\u003e116\"\u003c\/td\u003e \u003c\/tr\u003e   \u003ctr\u003e \u003ctd\u003eOverall width\u003c\/td\u003e \u003ctd\u003e138\"\u003c\/td\u003e \u003c\/tr\u003e   \u003ctr\u003e \u003ctd\u003eDistance between posts\u003c\/td\u003e \u003ctd\u003e112\"\u003c\/td\u003e \u003c\/tr\u003e   \u003ctr\u003e \u003ctd\u003eDrive-through width\u003c\/td\u003e \u003ctd\u003e102\"\u003c\/td\u003e \u003c\/tr\u003e   \u003ctr\u003e \u003ctd\u003eFront arm reach\u003c\/td\u003e \u003ctd\u003e29.50\" – 49.25\"\u003c\/td\u003e \u003c\/tr\u003e   \u003ctr\u003e \u003ctd\u003eRear arm reach\u003c\/td\u003e \u003ctd\u003e34.25\" – 49.25\"\u003c\/td\u003e \u003c\/tr\u003e   \u003ctr\u003e \u003ctd\u003eMaximum pad height\u003c\/td\u003e \u003ctd\u003e9\"\u003c\/td\u003e \u003c\/tr\u003e   \u003ctr\u003e \u003ctd\u003ePower supply\u003c\/td\u003e \u003ctd\u003e220V single-phase, 60 Hz\u003c\/td\u003e \u003c\/tr\u003e   \u003ctr\u003e \u003ctd\u003eHydraulic fluid\u003c\/td\u003e \u003ctd\u003eAW32, about 3 gallons\u003c\/td\u003e \u003c\/tr\u003e   \u003ctr\u003e \u003ctd\u003eHydraulic cylinders\u003c\/td\u003e \u003ctd\u003eDual (one per column)\u003c\/td\u003e \u003c\/tr\u003e   \u003ctr\u003e \u003ctd\u003eCertifications\u003c\/td\u003e \u003ctd\u003eISO 9001, CE\u003c\/td\u003e \u003c\/tr\u003e   \u003ctr\u003e \u003ctd\u003eConcrete requirement\u003c\/td\u003e \u003ctd\u003e4\" minimum thickness, 3,000 PSI minimum\u003c\/td\u003e \u003c\/tr\u003e   \u003ctr\u003e \u003ctd\u003eShipping weight\u003c\/td\u003e \u003ctd\u003e1,550 lbs\u003c\/td\u003e \u003c\/tr\u003e   \u003ctr\u003e\u003ctd colspan=\"2\"\u003e\u003cem\u003eInstalls on a level, cured concrete floor meeting the spec above. Confirm a dedicated 220V single-phase circuit (30-amp) is available before purchase.\u003c\/em\u003e\u003c\/td\u003e\u003c\/tr\u003e \u003c\/table\u003e  \u003ch2\u003eWarranty\u003c\/h2\u003e \u003cp\u003eThe Triumph NT-11 carries a \u003cstrong\u003e1-year parts warranty\u003c\/strong\u003e (no labor). Within the warranty period, Triumph troubleshoots the problem by phone, then ships the needed replacement part free of charge with free ground shipping. Rubber lifting pads are not covered. Hydraulic cylinders carry a 30-day full warranty, after which a seal kit is provided. Labor and freight are the owner's responsibility. Contact \u003ca href=\"mailto:sales@mygaragesupplies.com\"\u003esales@mygaragesupplies.com\u003c\/a\u003e or call \u003ca href=\"tel:+13073811810\"\u003e307-381-1810\u003c\/a\u003e to start a warranty claim.\u003c\/p\u003e  \u003ch2\u003eFAQ\u003c\/h2\u003e \u003ch3\u003eWhat can the NT-11 lift, and how is the capacity distributed?\u003c\/h3\u003e \u003cp\u003eRated capacity is 11,000 lb, distributed at 2,750 lb per arm pad across all four arms. The lift is designed to raise the entire vehicle on all four pads — never use it to raise only one end or one corner.\u003c\/p\u003e  \u003ch3\u003eWhat does \"asymmetric\" mean on this lift?\u003c\/h3\u003e \u003cp\u003eThe two front arms are shorter three-piece double-telescoping arms and the two rear arms are longer two-piece single-telescoping arms. That geometry sets the vehicle rearward of the column centerline, so the doors open clear of the columns when you get in and out — useful when you load passenger vehicles between the posts.\u003c\/p\u003e  \u003ch3\u003eWill it fit a shop with limited ceiling height?\u003c\/h3\u003e \u003cp\u003eThe floor-plate design has no overhead crossbar, so there is no top bar limiting clearance. The lift's tallest fixed point is the 116-inch (about 9-foot-8) column. Plan your ceiling for the column height plus the tallest vehicle raised to working height, and keep the area free of overhead obstructions such as heaters, building supports, and electrical lines.\u003c\/p\u003e  \u003ch3\u003eWhat concrete and electrical service does it need?\u003c\/h3\u003e \u003cp\u003eInstall on a level concrete floor that is a minimum of 4 inches thick and rated 3,000 PSI; do not install on asphalt, over expansion joints, outdoors, or on a second floor over a basement. The power unit runs on 220V single-phase service at 60 Hz on a dedicated 30-amp circuit. Have a certified electrician make the hook-up to comply with local code.\u003c\/p\u003e  \u003ch3\u003eIs installation included?\u003c\/h3\u003e \u003cp\u003eMGS does not include installation in the base price. The supplied manual covers site layout, anchor-bolt installation, power-unit mounting, cable routing, hydraulic hook-up, and test run. Triumph notes the lift can typically be assembled by two people in a few hours; many shop owners install in-house, and third-party installation is also common.\u003c\/p\u003e  \u003ch3\u003eHow is the lift delivered?\u003c\/h3\u003e \u003cp\u003eThe NT-11 ships freight on an LTL common carrier on a 48-foot semi truck. \u003cstrong\u003eYou are responsible for unloading the lift from the truck\u003c\/strong\u003e — the driver will not unload it for you, and lift-gate service is not available for auto lifts. Plan for a forklift, Bobcat, tractor, tow truck, or backhoe at the receiving location. If you cannot unload at your location, the lift can be shipped to the carrier's nearest freight terminal for pickup with a trailer or moving van. You are responsible for scheduling the delivery appointment with the freight company.\u003c\/p\u003e  \u003ch2\u003eDocuments\u003c\/h2\u003e \u003cp\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0771\/5550\/0318\/files\/nt-11-two-post-auto-lift-installation-manual.pdf?v=1780761724\" target=\"_blank\" rel=\"noopener noreferrer\" aria-label=\"Download the Triumph NT-11 installation and operation manual PDF, opens in new tab\"\u003eTriumph NT-11 Installation \u0026amp; Operation Manual (PDF)\u003c\/a\u003e\u003c\/p\u003e","brand":"Triumph","offers":[{"title":"Warehouse Pickup","offer_id":55049138209107,"sku":"NT-11","price":1557.0,"currency_code":"GBP","in_stock":true},{"title":"Ship to My Address","offer_id":55049138241875,"sku":"NT-11-S","price":1744.0,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1076\/9324\/4755\/files\/nt-11-two-post-auto-lift-hero.webp?v=1790261003","url":"https:\/\/progradewarehouse.com\/products\/nt-11-two-post-auto-lift","provider":"PRO GRADE WAREHOUSE","version":"1.0","type":"link"}